| Saber Electronics | TXQ RGB | TXQ SN-Pixel |
|---|---|---|
| Blade Illumination |
1 LED at the base of the blade illuminating the full length of the blade |
100+ LEDs that run the entire length of the blade |
| Recharge | USB or Removable Battery 2000mAh | USB or Removable Battery 3000mAh |
| Volume control | ✅ | ✅ |
| Motion & Hit Detection | ✅ | ✅ |
| Blaster Block, Clash, Lock-up effects | ✅ | ✅ |
| Sound fonts | 16 Including Luke, Kylo, Obi-wan, Anakin, Darth Vader, Ben Solo, Ahsoka, Rey, Palpatine, Lei and more. | 27 Including Luke, Emperor, Obi-wan, Electric Essence, Angelic Plasma, Jurassic, and more. Customizable w/ 32GB Micro SD |
| Blade Color Change | 12 Blade Colors; Red, Blue, Yellow, Cyan, Ice Blue, Green, Pink, Orange, Purple, Pink-Green, Rose, White | Unlimited RGB color settings |
| Smooth Swing | ✅ | ✅ |
| Force & Stab effects | ✅ | |
| Melt & Tip-drag effects | ✅ | |
| Activation Animations | ✅ | |
| Blade Effects | Stable, Pulse, Ghost, Blaster | Stable, Unstable, Pulse, Wave, Ghost, Cross, Infinite, Rainbow, Fire |
| Saber Ignition Effects | 9 Effects |
Buttons: There are two orientations for the Power and AUX buttons. If your saber buttons are vertical or up and down, the TOP button is Power and the BOTTOM button is AUX. If your saber buttons are horizontal or across the saber then the LEFT button is Power and the RIGHT button is AUX.
Blade Length: Before putting your saber in Standby Mode you can change the Blade length by tapping POWER 3 times. You will hear an announcement of the new blade length.
Stand By Mode: Enter Standby mode by holding POWER until hearing the announcement of 'Power On'
Auto Shut OFF: The saber will automatically power completely off after 10 minutes of nonuse to save battery.
While in Standby:
| Function | Control | Notes |
|---|---|---|
| Turn On | Tap the button | The Saber will turn on. |
| Power On Motion | Twist the Saber | This motion is a quick twist of the saber one way and back. |
| Volume Control | Hold the POWER and AUX button at the same time until you hear the beep then release | Adjust volume with POWER(UP) and AUX(DOWN) buttons then tab both again to set volume. |
| Switch Boot Effects | Hold the POWER button until you hear a beep then release | You will hear a confirmation of the new Boot Effect. |
| Switch Blade Effects | Hold the AUX button until you hear a been then release | You will hear a confirmation of the new Blade Effect. Stable, Unstable, Pulse, Ghost, Cross, Infinity, Wave, Rainbow, Fire |
| Switch Blade Effects Motion | Hold the Saber upward, hold AUX button and twist Saber | You will hear a confirmation of the new Blade Effect. Stable, Unstable, Pulse, Ghost, Cross, Infinity, Wave, Rainbow, Fire |
| Sound Font Selection | Tap AUX | You will hear a sound confirming the switch. |
While On:
| Function | Control | Notes |
|---|---|---|
| Blaster Deflection | Tap the AUX button | |
| Lock Up | Hold the AUX button | |
| Color Change | Point the Saber blade downwards, hold the AUX button and twist the saber | |
| Flash on Clash on/off | Hold POWER and AUX buttons at the same time until you hear the beep then release | |
| Turn Off | Tap POWER Button | |
| Turn OFF Motion | Twist the Saber | This motion is a quick twist of the saber one way and back. |
| Drag | Hold the POWER button then hit the saber. | |
| Melt | Hold the AUX button then thrust the saber horizontally forward. | |
| Force | When the Blade is up hold the AUX button then twist the saber. |